LED display summer practical manual

Faced with the special environment of high temperature, rainy and thunder in summer, it is not only dependent on the high-strength weather resistance of the LED display itself. In many cases, the omission in construction and post-maintenance is the result of shortening the life of the LED display and various failures. Hidden danger!

For this purpose, we have some experience in lightning protection, high-temperature heat dissipation and waterproofing for your reference!

LED display summer lightning protection

1. Protection against direct lightning strikes: Install a lightning rod on the support structure of the LED display (outdoor), an indoor LED display or an LED display with tall buildings next to it, you may not need to install a lightning rod.

2. Counterattack against steel structure: Connect the rigid structure to the outer casing of the LED display, do the equipotential, and do the grounding. The grounding resistance is generally less than 10 ohms. If the resistance does not meet the requirements, it will be added. Artificial grounding grid. The lightning arrester should also be grounded.

3. For the lightning current induced on the power line: install a single-phase or three-phase power supply lightning protection device on the power line. The cross-sectional area of ​​the link line of the phase line shall not be less than 10 mm square, and the cross-sectional area of ​​the connection ground line shall not be less than 16 mm square.

4. For the lightning current induced on the signal line: install a signal lightning arrester on the signal line. The signal lightning arrester depends on the signal interface of the system. If it is a network cable, install a network signal lightning arrester, and the serial interface installs a DB9 interface lightning protection device. The cross-sectional area of ​​the grounding wire should not be less than 1.5mm square.

5, and the induced current with lightning strikes: unified with professional distribution boxes, cabinets can more comprehensive and effective protection of the entire circuit system for lightning induced current interference.

LED display cooling in summer

1, 20 square inch LED display

It is generally not recommended to use air conditioners. If conditions permit, use two fans with a diameter of about 500mm, depending on the size of the installation space.

2, more than 20 square meters of LED display

1) If the LED display is installed against the wall and can protrude from the wall by one meter, it is recommended to select the fan according to the size of the area. The fan installation position is arranged above the side of the screen. If you buy a display with an 80-square-meter ph16 outdoor LED full-color screen, it means that you need 6 fans with a diameter of 600mm, the fan is the one that draws air outside, and the fan is installed. When you want to ensure that there is a net inside, to prevent the technicians who repair the display screen from sucking other things into the adult body when repairing the display screen. In order to waterproof, install the fan outlet on the outer aluminum-plastic panel. Aluminum shutters.

The wall-mounted LED display can also be installed with air conditioning, ensuring sufficient space for the air-conditioning main unit without affecting the overall appearance of the wall. The choice of air conditioning is required, and the most commonly used air conditioners are 1.5P, 2P and 3P. The northern city uses 12 square 1P air conditioning calculation; the southern city uses 9 square 1P air conditioning calculation. If the area of ​​the LED outdoor display is relatively large, the air conditioner needs to be customized; if the area is not large, you can go to the store to buy it, but you need to buy a display cooling air conditioner with caller compensation function.

2) If the LED display is installed in a column, it is best to use a fan to dissipate heat. The fan is installed on the back of the large screen. The aluminum-plastic panel is placed on the top of the large screen to form a blind so that the rain does not enter the display when it rains. . In the case of a double-column LED display, several louvers can be opened in the middle of the double column. This window is the air inlet and the upper fan is the exhaust port, so that complete air convection makes the heat dissipation better.

3) If the air conditioner must be installed, the purchase cost and the use cost should be increased, and the heat dissipation effect will be worse than the fan. It is also necessary to consider the space in which the air conditioner is installed in the space, and whether the overall appearance can be ensured.

LED display waterproof in summer

The display screen is mainly waterproof. The selected module should be an outdoor waterproof module. The back of the module should be painted with three anti-paints. The selected box should also be a waterproof case with good sealing. The other part needs to be implemented in the specific construction site; in the structural design, the combination of prevention and drainage; after the structure is determined, according to the characteristics of the structure, it can be considered to have a hollow bubble tube structure, a small compression set rate, and an elongation at break. Large performance sealing strip material; after selecting the sealing strip material, it is necessary to design a suitable contact surface and contact force according to the characteristics of the sealing strip material, so that the sealing strip is pressed into a dense shape. In some installations, waterproof tanks, etc., focus on protection, to ensure that there is no water inside the display. This will ensure that the display will not have any quality problems caused by human factors during the rainy season.

Secondly, for different cell board materials, a professional waterproof coating is needed. Here, the user's p10 full-color outdoor LED display is taken as an example. First of all, confirm whether the ph10 outdoor unit board is magnet adsorption or screwing (the screw effect is good, the magnet is slightly worse); secondly, there is no waterproof groove on the unit board kit, if there is any, the front waterproof is basically not a big problem, even the unit board It is no problem if it is fixed with a magnet.

Finally, we also need to pay attention to the waterproof problem of the back panel of the outdoor LED display, because in the process of using the display, the back panel LED display is not only heat-dissipating, but also has great convenience in dealing with waterproof performance. Sex. When dealing with the waterproof coating on the back side, pay more attention to the waterproof performance of the aluminum strip in the back strip display. It is necessary to use the electric drill to design a row of drains under the aluminum-plastic panel, which is beneficial to the waterproof display and the heat dissipation of the display. The best display processing method.