store In order to prevent moisture, the LEDs should be stored in a dry and ventilated environment with a storage temperature of -40 ° C - + 100 ° C and a relative humidity of 85% or less. The LED is preferably used within 3 months of its original packaging conditions to avoid rusting the bracket. When the LED packaging bag is opened, it should be used as soon as possible. At this time, the storage temperature is 5°C-30°C, and the relative humidity is below 60%. clean Do not use unknown chemical liquids to clean the LEDs, as this may damage the surface of the LED resin and even cause colloidal cracks. If necessary, please immerse the LEDs in alcohol or fluorinated argon at room temperature for one minute. Forming Do not form during or after welding. If necessary, the forming must be completed before welding. It is important to remember that the behavior of any extruded resin can damage the gold wire inside the LED. welding During the welding process, do not apply any external pressure to the lamp body, otherwise cracks may appear inside the LED, which may affect the internal gold wire connection and cause quality problems. The gel must not be immersed in the solder. When welding, the solder joint should have at least 2 mm clearance from the lower edge of the colloid. After the soldering is completed, it is necessary to use three minutes to return the LED from a high temperature state to a normal temperature. If soldering a linearly arranged LED on the same PCB with a soldering iron, do not solder the two pins of the same LED at the same time. A soldering iron of 30W or less is required for soldering iron soldering. There are two specifications for LED soldering. The specific parameters are as follows: Soldering iron soldering temperature: 295 °C ± 5 °C Welding time: within 3 seconds (only once) Wave soldering soldering temperature: 235 ° C ± 5 ° C soldering time: within 3 seconds Note: Improper soldering temperature or time control may cause the LED lens to deform or open the inside of the wick to cause a dead light. Recommended method In the use of single or multiple use, the DC drive current of each LED is recommended to use IF range of 10mA-20mA. Instantaneous pulses can damage the internal fixed connections of the LEDs, so the circuit must be carefully designed so that the LEDs are not subject to overvoltage (overcurrent) shock when the line is opened and closed. LEDs require uniform brightness and color when used in multiple applications. Therefore, we must fully understand the driving method and driving conditions. Under normal conditions, we guarantee the consistency of color and brightness of 20 mA splitting. To achieve uniform brightness and color, the same current should be used for the same batch of LEDs. Do not mix them in use to avoid brightness differences. The relationship between the VF, IF, IV, WL and temperature of the LED is detailed in the product specification. ESD (static protection) Static electricity can cause LED function failure. It is recommended to prevent ESD from damaging the LED. A. The operator must bring an anti-static wrist strap and anti-static gloves when testing and assembling the LED. B. Welding equipment and test equipment, work tables, storage racks, etc. must be well grounded. C. Use an ion fan to eliminate static electricity generated by the LED during storage and assembly due to friction. D. The box with LED is made of anti-static material box, and the bag is made of electrostatic bag. The anomalies that can be caused by ESD-damaged LEDs are: A, reverse leakage, light will cause the brightness to decrease, in severe cases the light does not light. B. The forward voltage value becomes smaller. The LED does not emit light when driven at low current.
Crawler tractors are versatile,domestic initiative and technology leading. Hydraulic controlled differential - brake turn to technology , 360 degree steering wheel control and spin turn are our company`s unique advantages. In addition, our products also have the superiorities of triangular track drive, low grounding pressure and better Paddy field performance. Our company has iron crawler tractor and Rubber Crawler Tractor, which two main products. Every products have different types. These products are of high efficiency, long operating life. and low fuel consumption. Our crawler tractors are easy switching between hydraulic infinitely variable speed and mechanical transmission.
If you have any questions, please contact with us directly. Crawler tractors are produced by our company with high quality and good appearance. Welcome you can visit our factory.for inqury, Please send mail directly to us!
Rubber Crawler Tractor Small Crawler Tractor,Rubber Crawler Tractor,Triangular Crawler Structure,Convenient Control Crawler Tractor Hunan NongFu Machinery&Electronic.Co., Ltd. , https://www.nfagmachine.com