The design principle of electronic hypnosis 1. Circuit principle The circuit of the raindrop sound electronic hypnotic device is shown in Figure 1. The circuit consists of: a high-voltage generator, a rectifier and two neon bubble relaxation oscillators. The high-voltage generator is composed of triode VT, coils L1-L3, etc. After pressing the switch "SB", the inductive feedback oscillator composed of L1, L2 and VT immediately starts to oscillate, and the oscillating voltage is boosted by coil L to obtain about 300 V high pressure. This high voltage is rectified by the diode VD to charge the capacitor C1, so a high voltage DC source can be obtained across the capacitor C1. The neon bulb V1, piezoelectric ceramic sheet B1, resistor R2 and V2, B2, R3 respectively constitute two relaxation oscillators, and its starting principle: the DC high voltage source of C1 passes through the resistors R2, R3 to the piezoelectric ceramic sheets B1, B2 respectively Charging (HTD ～ 27 A-type ceramic sheet has a capacitance of about 0.017uF), when this voltage is charged to the start-up voltage of neon bulb V1 (or V2) (about 60 ～ 80 V), the neon bulb discharge is turned on, piezoelectric The charge accumulated on the ceramic sheet is discharged, and the voltage drops. When it drops to the neon bubble's ignition voltage, the neon bubble stops glowing and turns off. The piezoelectric ceramic sheet will continue to charge through the resistors R2 and R3, making the voltage continuous Ascending ... so oscillating repeatedly. During the discharge of the piezoelectric ceramic sheet, the voltage across its two ends changes greatly. Due to the piezoelectric effect, the piezoelectric ceramics vibrate mechanically, so it emits a "click, click" sound similar to the sound of raindrops. The novel hypnotic device introduced here can emit a raindrop sound with a double sound effect and has a good hypnotic effect. 2. Component selection and production VT can use 3AX31B and other germanium PNP transistors, β≥50, VD can use 1N4007 and other silicon rectifier diodes, V1 and V2 can use NH0-4L and other neon bubbles with a starting voltage of about 60 to 80V. R1 ～ R3 all use RTX-118W type carbon film resistors. If 100 MΩ high resistance resistors cannot be found, several resistors can be used in series. C1 requires the use of electrolytic capacitors with a voltage of 400 V or more. The transformer T needs to be self-made: it is wound with a GU18 type magnetic tank, 20 turns for L1, 30 turns for L2, and 500 turns for L3. They are all wound with Φ0.1 mm high-strength polyester enameled wire. G uses a large battery, "SB" is a small normally-open light touch key switch, and the piezoelectric ceramic sheet can use HTD-27A type. The circuit of this machine is relatively simple, and there is no need to make a printed circuit board. It can be directly connected and installed in the plastic box with a terminal frame. In order to increase the volume, a plastic acoustic cavity should be made for the piezoelectric ceramic sheet, or a circular hole slightly smaller than the ceramic sheet can be opened in the plastic machine box, and then the piezoelectric ceramic sheet is pasted in the circular hole with epoxy resin In the first place, using the machine box as the auxiliary sound cavity has a very good effect. 3. Circuit debugging First adjust the resistance R so that the voltage on the capacitor C1 is around 250-300 V. If the voltage cannot be adjusted up, the number of turns of the coil L3 may be too small. If there is no voltage at both ends of C1, it means that the high-voltage generator has not started to vibrate. It may be that the coils L1 and L2 are connected with the same name. The only problem is to adjust the two ends of L1 (or L2). The resistance of the resistor L2 (or L3) and the capacitance of the piezoelectric ceramic sheet B1 (or B2) will determine the level of the oscillation frequency. If the capacitance of the piezoelectric ceramic sheet is too small, the frequency of the raindrop sound will be too high and affect the hypnotic effect At this time, as long as the resistance of the resistor R2 (or R3) is large, it can be solved. 4. Use Just press the switch "SB" before going to sleep, the capacitor C1 will be full of high voltage. The two relaxation oscillators start to oscillate immediately. Due to the discrete nature of the circuit elements, the oscillation frequencies of the two oscillators cannot be exactly the same, so they can produce double-sound raindrop sounds. When the switch "SB" is just pressed, the frequency of the raindrop sound will change from low to high, indicating that the voltage across C1 is increasing. After about 4 to 5 s (seconds), the tone will no longer rise, indicating that the voltage across C1 has Charge to the highest value. After releasing "SB", the hypnotic sound is a bit like the sound of wooden fish in the temple. Later, as the voltage across C1 drops, the hypnotic sound tone also drops, like the sound of raindrops. Later, it was like the two drops of water falling from the eaves, the sound of falling in the water tank, and the last drop of water chased the previous drop of water, which is due to the difference in frequency of the two oscillators. When about one drop per second, the voltage across C1 is less than the ignition voltage of the piezoelectric ceramic sheet, the circuit stops vibrating, and the piezoelectric ceramic sheet no longer produces sound. The circuit no longer consumes power. If you are not asleep at this time, you can press the switch "SB" again. Since the neon bubble relaxation oscillator consumes no electrode during operation, the circuit can work continuously for 40 to 50 minutes (minutes) each time SB is pressed. If you need to extend the working time, you can increase the capacity of capacitor C1. If the leakage current of capacitor C1 is large, it will greatly reduce the working time of the circuit after each key press, so you must pay attention to the size of the leakage current when selecting C1.
Full Spectrum Led Grow Lights 600/900/1200W /2000W Double Chips Led Grow Lights Indoor Plants lamp for flowering and growing
Product Description
How to Select the Best Grow Light for your Greenhouse?
The plant needs light to thrive cause the light is essental for photosynthesis.without it,plants can not make food.but light can also be too intense,too hot or last too long for growing healthy plants.plant growth accelerates with abundant light because more of the plant`s leaves have exposure,which means more photosynthesis.in the winter,days are not long enough,but many plants still need 12 hours or more of light per day.
Dual Veg and Bloom for plant growth and bloom
Installs and operates simply
Long lifespan
Our professional full spectrum LED grow lights are suitable for all the indoor plants and good for seeding, growth,flowering and fruiting stages of plants, increasing the harvest and Saving energy.
User manual:
Our Advantages
Professional: we are professional LED Grow Lights and Led Aquarium Light manufactuer here in China, you will get Professional and High quality LED Grow Lights and Led Aquarium Lighting from us and get good guarantee.
Cost-effective Price: we don`t have the lowest price, but the grow lights and Aquarium Light you get from us really cost-effective, good quality & decent price.
Win-win situation: Long term business is our mission, we think you will agree with us if you are running a business, so we will provide good led aquarium grow lights and warming service to build a long-term business relationship with you
24/7 unlimted customer service: we are always here for you for your question, any question just email us or call us, we will do our best to help you all the way.
Long term warranty: Don`t worry about the quality and we guarantee you 3years warranty for all the LED Plant Grow Light and Coral Reef Led Aquarium Light..
Best buying experience: you will get the tiptop serive you have ever had,just have a try and you`ll see.
Philizon Fulll Spectrum LED grow lights are perfect for green house applications and much more!
Full Spectrum Led Grow Lights,Full Spectrum Plant Grow Light,Full Spectrum Led Plant Grow Light,Full Spectrum Indoor Plant Grow Light Shenzhen Phlizon Technology Co.,Ltd. , https://www.philizon.com
1. Comply with the safety requirements around the world
2. High power LED,Life 50,000 hours
3. Energy saving 80%,compared to sodium lamp sand metal halide lamps
4. Fan cooling,low temperature rise
5. A variety of LED chip synthesis spectrum.
6. Input: AC100~277V,PF >0.9
7. Recommended irradiation distance of 0.5 ~ 0.8m,Coverage 0.7m @ 6m2
8. Warranty:3 years
9. CE RoHS FCC.UL
Now,adding LED Grow Lights to your greenhouse is an nice choice if you live in the north, and can not get enough daylight in winter.you might be take HID into consideration,cause it has high output and cover a wide area.but now,we providing you some dfferent.the newest type of grow lights use LED technology.
Provides Maximum Light Density and optimizing spectrum(410nm-740nm,white)
as we know that the plants need more light from the blue side of the spectrum during their seedling stage and when developing foliage and require light from the orange to red side of the spectrum while inblooming and fruiting phases. We adopting lastest intergrated COB technology, white , more red and blue PAR(410-740nm) per Watt than any other lighting fixture for the best color uniformity.
the Led grow lights feature selectable VEG and BLOOM light spectrums to deliver maximum performance from seeding through the flower stage and finally harvest.
Increase yields and potency
using high quality lense that hyper-focus the lights on your canopy.the photons are beamed directly to the plants.this gives growers the ability to get greatest possible crop yield.
Reduce your costs with energy efficiency
energy-efficient cannabis grow lights cost between 40%-60% less to operate compared to HID lam year.
Led Grow Light also eliminate the needs for ballasts and reflectors while they minimize the cooling systems,accelerating your payback.you will see the electrical bills trimmed by approximately half,year after year.
the input voltage is AC100V-240V,fit for the world standard,built-in power supply.do not need other equipment,just access to the Plug,the lamp will be work smoothly. The Led Grow Lighting is small size,just few inches and easy to install.it is the good option for some greenhouse.
using built-in quiet fans and the shutter in the wind,induced draftfrom all sides.runs with quiet. Useadvanced isolation power supply and soft start protection technology, to prevent the high voltage when turn on the light from damagingthe lamp body.
1>Indoor and green house use only
2>Do not touch the surface when the power is on
3>Do not use it at the place where the water is dripping
4>Blue is good for vegetative and red is good for flowering and budding, customer can choose the ratio of the red and blue, which has wonderful efficacy for the plants