Thanks to Yi Xun for giving me this opportunity to try out the Cooler Master BOX5 chassis. It took a long time from participating in the official release. Don't want to talk too much nonsense. Go straight to the topic. Summarized part remember to take a look 喔~~~ The front of the chassis does not use the cool shape of the game chassis, but uses a very simple mesh design. The advantage of the translucent design is that it can provide considerable air intake space, so the thermal performance of the chassis will not be too bad. The inadequacies are also more obvious, that is, the shape is not cool enough . The interior of the chassis is relatively wide, and the power section has a cover that makes the overall look more beautiful. The right side of the chassis is a bracket for storing the storage device. The tool-free design is used to directly mount the bracket.  The use of buckles is very convenient, and people who have used them are good. Toolless installation refers to the tool-free installation of a 3.5 -inch hard disk. If it is 2.5 inches, it still requires a screw fastening, such as an SSD . Here is the installation of SSD . Simply remove the mounting bracket screws and remove the bracket. , The baffle of the power supply is detachable. If the power supply is too large or the power cable is too large, the baffle can be disassembled. The card snaps into place when the bezel is installed. The upper part of the baffle also has a hole through which the wire can exit. The bracket of the storage device is detachable, and the screws of the bracket can be loosened. The lower bracket can be removed and the upper bracket can also be removed. After the bracket is disassembled, the internal space increases, allowing players to install longer graphics cards. Fans are provided at the rear and front of the chassis. The supplied fan is nothing special, more common, it is recommended to replace the fan with LED lighting effect. The mounting holes on the main board of the chassis are all labeled. Different versions have corresponding holes. For example, A refers to the mounting hole of the ATX main board. The M next to the sign is to install the M-ATX motherboard. The chassis supports seven-slot motherboards. The general motherboard is seven slots. The self-used game will have ten slots in the tiger shark chassis, and the entire interior of the chassis is wider. The slot of the chassis adopts a removable baffle design. Personally, it prefers the detachable one compared to the disposable baffle. The inner plate of the chassis has a curled design, and the details are still good. There is a filter in the lower part of the power supply, and the filter can be withdrawn directly by hand. Chassis I/O wiring, the chassis is only equipped with USB 3.0 interface, interface is not much. The restart button is really too small. Don't you make it bigger? The height of the chassis's feet is about 3cm , and the bottom is high enough. It is not afraid that the power supply will affect the heat dissipation because it is too close to the ground. If you do not remove the storage bracket, the chassis can accommodate about 30cm long video card, this length can basically "eat" most of the commercially available graphics card.  The front panel of the chassis can accommodate three fans. The front of the chassis is equipped with a front fan. Unfortunately , the fan is not equipped with LEDs . This time we settled on the BOX5 accessories, ASRock Z97 motherboard, GALAXY GTX 960 graphics card, GALAXY HOF power supply, and two SSDs . what is this? The Phillips screwdriver turns the small accessory of the sleeve and is very practical. The general family does not have a matching outfit. The size of the sleeve of this gadget is the same as that of the motherboard. When mounting, it is only necessary to insert the sleeve into the mounting screw, and then tighten it with a screwdriver. My motherboard is the Z97 , but it looks like it is a little incompatible with the motherboard. The mainboard reserved ATX motherboard location, my motherboard is not on. This is the fan's mounting accessories, usage is very simple, first put the sleeve into the fan's mounting hole, and then insert it, it is OK . The actual effect is shown in the figure.  The route is very food, ignore it directly. Summary: The highlight of BOX5 is not a lot, really not a lot. Surprisingly, the chassis uses a modular design concept, whether it is a hard disk cage, SSD bracket, or a power enclosure. The estimation is also based on the modularization concept. Cooler also introduced the Maker chassis. The Maker chassis has a better module than the BOX5. A bit far away, or talk about BOX5. The internal space of the chassis is indeed very large, and the cabling is relatively easy. Unfortunately, my cabling technology is not closed, and the interior is so bad that it affects everyone's perception. If you want to do a better job, it is estimated that you should give up some fans to be more beautiful. The chassis uses a side-through design. If you don't like light pollution, the benefits of side penetration cannot be enjoyed. The appearance of BOX5 is very low-key, compared with those chassis products that flaunt the game chassis, BOX5 is relatively low-key. The entire installation process is still relatively smooth, and the gadgets that come with the chassis are very pleasant. Unfortunately, screws are not enough, just enough. Inadequate: 1 , the appearance of more simple; 2. The restart button is a bit small; 3 , I / O interface is not rich enough, only the standard two USB 3.0 interface  Likes: 1 , modular design is relatively new, removable components to enhance the internal space of the chassis; 2. The internal space of the chassis is wide, and the cabling is relatively easy; 3 , the included gadgets are very practical, the Phillips screwdriver sleeve is very practical, free tool fan accessories are awesome; Fiber Optic Box,Fiber Optics Box,Fiber Optic Boxes,Fiber Optic Junction Box Cixi Dani Plastic Products Co.,Ltd , https://www.danifiberoptic.com
